Search Results

A Three-Way Catalyst (TWC) model with global TWC kinetics for lean burn DISI engines were developed and validated. The model incorporates kinetics of hydrocarbons and carbon monoxide oxidations, NOx reduction, water-gas and steam reforming and oxygen storage. Ammonia (NH₃) and new nitrous oxide (N₂O) kinetics were added into the model to study NH₃ and N₂O formation in TWC systems. The model was validated over a wide range of engine operating conditions using various types of experimental data from a lean burn automotive SIDI engine. First, well-controlled time-resolved steady state data were used for calibration and initial model tests. In these steady state operations, the engine was switched between lean and rich conditions for NOx emission control. Then, the model was further validated using a large set of time-averaged steady state data. Temperature dependencies of NH₃ and N₂O kinetics in the TWC model were examined and well captured by the model.

A fundamentally based quasi-dimensional NOx emission model for spark ignition direct injection (SIDI) gasoline engines was developed. The NOx model consists of a chemical mechanism and three sub-models. The classical extended Zeldovich mechanism and N₂O pathway for NOx formation mechanism were employed as the chemical mechanism in the model. A characteristic time model for the radical species H, O and OH was incorporated to account for non-equilibrium of radical species during combustion. A model of homogeneity which correlates fundamental dimensionless numbers and mixing time was developed to model the air-fuel mixing and inhomogeneity of the charge. Since temperature has a dominant effect on NOx emission, a flame temperature correlation was developed to model the flame temperature during the combustion for NOx calculation. Measured NOx emission data from a single-cylinder SIDI research engine at different operating conditions was used to validate the NOx model.

Using non-viscosity dynamic structure Large Eddy Simulations (LES) turbulence model, spray=induced turbulence is investigated on a number of different Computational Fluid Dynamics (CFD) grids of varying mesh sizes (from 0.5 to 2 mm mesh). Turbulent flow is induced inside a quiescent chamber by liquid fuel spray and then left to decay after end of injection by virtue of its molecular viscosity and turbulent dissipation. Coherent structures (CS) of this turbulent flow are constructed and visualized using λ2 definition. Using CS, analysis is performed on the turbulent flow around the liquid spray jet. These CS from LES are then compared against the results from RANS calculations as well. The visualization of CS helps to explain the mechanism of fuel-air mixing obtained from LES results and its difference with RANS calculations.

Numerical investigation is carried out to explore various strategies of combustion mode switching in a diesel engine operating at high power. Numerical results are compared with high power single cylinder (CAT 3401E) experiments for combustion phasing and emission characteristics. In this study CFD calculations are carried out using the KIVA CFD code with Large Eddy Simulation turbulence model and Direct Chemistry Solver sub-models. The advanced turbulence and combustion sub-models enabled more realistic visualization of the effects of single-cycle mode switching on in-cylinder flow structures, fuel-air mixing behavior and combustion phasing. Two circumstances of mode switch are presented in this study. Mode switches are performed from traditional High Temperature Combustion to early injection PCCI combustion and vice versa. In this investigation several aspects of combustion control are investigated.

Numerical investigation is carried out in order to explore diesel combustion using advanced turbulence and combustion models. Turbulence is modeled by one-equation non-viscosity dynamic structure Large Eddy Simulation (LES) model. Sub-grid fuel-air mixing is calculated using a dynamic scale similarity sub-grid scalar dissipation model to represent the local state of combustion. Fuel-air mixing time scale is used in order to determine the local in-homogeneity and rate of mixing of fuel and air. Diesel combustion is studied and compared with experimental results for high power diesel engine setup at different conditions representing both low temperature combustion and traditional high temperature combustion regimes. Further studies are carried out in diesel engine to investigate in-cylinder fuel air mixing and the onset of ignition.

A novel algebraic similarity model for subgrid scalar dissipation rate has been developed as part of the Large Eddy Simulation (LES) package KIVA3V-LES for diesel engine study. The model is proposed from an a priori study using Direct Numerical Simulation (DNS) of forced isotropic turbulence. In the a posteriori test, fully resolved turbulent passive scalar field measurements are used to validate the model in actual engine flows. For reason of the length limit by SAE and the specific interest in engine applications, only a prior test and a posteriori test in engine flows are included in this paper. A posteriori tests in isotropic cube flow, turbulent round jet and flame cases will be presented in separate papers. An engine LES simulation of multi consecutive cycles was performed in this study.

Diesel engine combustion is simulated using Large Eddy Simulation (LES) with a multi-mode combustion (MMC) model. The MMC model is based on the combination of chemical kinetics, chemical equilibrium, and quasi-steady flamelet calculations in different local combustion regimes. The local combustion regime is identified by two combustion indices based on the local temperature and the extent of mixture homogeneity. The LES turbulence model uses the dynamic structure model (DSM) for sub-grid stresses. A new spray model in the LES context is used, and the Reynolds-averaged Navier-Stokes (RANS) based wall model is retained with the LES derived scales. These models are incorporated in the KIVA3V-ERC-Release 2 code for engine combustion simulations. A wide range of diesel engine operating conditions were chosen to validate the combustion model.

Detailed knowledge of hydrocarbon fuel combustion chemistry has grown tremendously in recent years. However, the gap between detailed chemistry and computational fluid dynamics (CFD) remains, because of the high cost of solving detailed chemistry in a large number of computational cells. This paper presents the results of applying a suite of techniques aimed at closing this gap. The techniques include use of a surrogate blend optimizer and a guided mechanism reduction methodology, as well as advanced methods for efficiently and accurately coupling the pre-reduced kinetic models with the multidimensional transport equations. The advanced methods include dynamic adaptive chemistry (DAC) and dynamic cell clustering (DCC) algorithms.

Two different types of mesh used for diesel combustion with the KIVA-4 code are compared. One is a well established conventional KIVA-3 type polar mesh. The other is a non-polar mesh with uniform size throughout the piston bowl so as to reduce the number of cells and to improve the quality of the cell shapes around the cylinder axis which can contain many fuel droplets that affect prediction accuracy and the computational time. This mesh is specialized for the KIVA-4 code which employs an unstructured mesh. To prevent dramatic changes in spray penetration caused by the difference in cell size between the two types of mesh, a recently developed spray model which reduces mesh dependency of the droplet behavior has been implemented. For the ignition and combustion models, the Shell model and characteristic time combustion (CTC) model are employed.

Fundamental simulations in a quiescent cell under adiabatic conditions were made to understand the effect of temperature, equivalence ratio and the components of the recirculated exhaust gas, viz., CO2 and H2O, on the combustion of n-Heptane. Simulations were made in single phase in which evaporated n-Heptane was uniformly distributed in the domain. Computations were made for two different temperatures and four different EGR levels. CO2 or H2O or N2was used as EGR. It was found that the initiation of the main combustion process was primarily determined by two competing factors, i.e., the amount of initial OH concentration in the domain and the specific heat of the mixture. Further, initial OH concentration can be controlled by the manipulating the ambient temperature in the domain, and the specific heat capacity of the mixture via the mixture composition. In addition to these, the pre combustion and the subsequent post combustion can also be controlled via the equivalence ratio.

Fundamental simulations using DNS type procedures were used to investigate the ignition, combustion characteristics and the lift-off trends of a spatially evolving turbulent liquid fuel jet. In particular, the spatially evolving n-Heptane spray injected in a two-dimensional rectangular domain with an engine like environment was investigated. The computational results were compared to the experimental observations from an optical engine as reported in the literature. It was found that an initial fuel rich combustion downstream of the spray tip is followed by diffusion combustion. Investigations were also made to understand the effects of injection velocity, ambient temperature and the droplet radius on the lift-off length. For each of these parameters three different values in a given range were chosen. For both injection velocity and droplet radius, an increase resulted in a near linear increase in the lift-off length.

Gas-phase in-cylinder mixing was examined by two different methods. The first method for observing mixing involved planar Mie scattering measurements of the instantaneous number density of silicon oil droplets which were introduced to the in-cylinder flow. The local value of the number density was assumed to be representative of the local gas concentration. Because the objective was to observe the rate in which gas concentration gradients change, to provide gradients in number density, droplets were admitted into the engine through only one of the two intake ports. Air only flowed through the other port. Three different techniques were used in analyzing the droplet images to determine the spatially dependent particle number density. Direct counting, a filtering technique, and autocorrelation were used and compared. Further, numerical experiments were performed with the autocorrelation method to check its effectiveness for determination of particle number density.

Various single and split injection schemes are studied to provide a better understanding of fuel distribution during cold starting in DI diesel engines. Improved spray-wall interaction, fuel film and multicomponent vaporization models are used to analyze the combustion processes. Better combustion characteristics are obtained for the split injection schemes than with a single injection. An analysis of the fuel impingement processes identifies the mechanisms involved in producing the differences in vaporization and combustion of the fuel. A greater amount of splashing occurred for the split injections compared to a single injection. This behavior is attributed to the decreased film thickness (less dissipation of impingement energy), the decreased impingement area (obtained by increasing the impingement Weber number), and most importantly, the reduced frequency of drop impingement.

Part I provides a review of present designs, advanced concepts and technologies needed for the next generation of high power density diesels for midrange truck application. Part II emphasizes the use of advanced computational tools to determine the most promising design parameters for high power density diesels which are suitable for truck application. Three types of analyses are reviewed and deemed necessary for design optimization at high power density conditions, these include: I. High BMEP cycle analysis based on zero dimensional thermodynamic analysis and engine similarity rules. II. Matching of advanced turbocharging systems for high torque rise engines. III. Multi-dimensional in-cylinder computational combustion fluid dynamics (CCFD). This analytical exercise indicates that computational tools are capable of rationalizing experimental results and therefore predicting engine performance in the conceptual stage.

A modified version of the three dimensional CFD code KIVA-3, which accommodates moving valves and a moving piston crown, has been applied to a heavy-duty, four cycle, dual intake valve, direct injection, diesel engine The fluid domain encompasses an intake runner, two valved ports and a cylinder with a Mexican hat bowl-in-piston configuration In the first part of the study, the modified KIVA-3 code was used to simulate the flow through the port and cylinder of the engine without a piston The intake valves were cycled (300 rpm at the camshaft) Two turbulence models were compared in this part of the study, standard k - ε and the RNG modified k - ε as discussed in [11] The results were compared to particle image velocimetry (PIV) images Large scale flow features of the computer simulations agreed moderately well with the ensemble averaged flow bench results There was very little difference between the results from the two turbulence models Motored engine simulations including a piston were conducted to characterize the in-cylinder gas flow and mixing during the intake and compression strokes Characterization methods were developed which yield insight into the in-cylinder gas motion and mixing during both strokes Intake and residual gases are tracked separately, both large scale convection and turbulent mixing are investigated, flow critical points are examined to provide information about flow topology and turbulence production is correlated with the evolution of flow structures Results show that mixing of the intake and residual gases is very non-uniform Many complex flow structures develop during intake and are destroyed during compression However, several structures survive through compression and contribute to enhanced mixing near top dead center These significant structures have been identified and tracked back to intake The flow field near top dead center exhibits spatial inhomogeneities in temperature and small scale mixing parameters such as turbulence kinetic energy and its dissipation rate